มอเตอร์ รวม สามเฟส มอเตอร์ และ เฟสเดียว มอเตอร์% 2C และ เฟสเดียว มอเตอร์ มี สาม สายไฟ และ หก สายไฟ
% 0athree เฟส มอเตอร์
% 0a สามเฟส มอเตอร์ สามเฟส ขดลวด 6 แตะ เรา เริ่มต้น โดย ถอด เชื่อมต่อ ชิ้น ที่ เชื่อมต่อ มอเตอร์ ขั้ว ใช้ a มัลติมิเตอร์ ถึง วัด แรก และ สุดท้าย สิ้นสุด ของ แต่ละ เฟส คดเคี้ยว ถึง ดู ถ้า มัน เป็น บน หรือ ปิด จากนั้น ใช้ a มัลติมิเตอร์ ถึง วัด ความต้านทาน ค่า ระหว่าง แต่ละ สองเฟส ขดลวด% 2c ที่ อย่างน้อย มากกว่า กว่า 7b% 7b% 7b4% 7d% 7d.5 megohm% 2c ใหญ่ ดีกว่า ในที่สุด% 2c วัด ฉนวน ฉนวน ความต้านทาน ของ แต่ละ เฟส ขดลวด และ มอเตอร์ ปลอก% 2c ซึ่ง ควร ยัง เป็น ไม่มีที่สิ้นสุด นี้ การวัด สามารถ โดยทั่วไป ตัดสิน คุณภาพ ของ สามเฟส มอเตอร์
% 0a ทิศทางเดียว มอเตอร์ มี เพียง สอง ขดลวด% 2c a เริ่มต้น คดเคี้ยว และ a วิ่ง คดเคี้ยว หนึ่ง ของ สาม สายไฟ เป็น ของพวกเขา ทั่วไป ลวด% 2c ที่ เป็น% 2c หนึ่ง ปลาย ของ สองเฟส ขดลวด เป็น เชื่อมต่อ ด้วยกัน อื่น ๆ สอง เป็น อื่น ๆ แตะ ของ สองเฟส ขดลวด
% 0aThe resistance between the two taps should be max and equal to the sum of the resistance values of the two windings
Of course, we also need to measure the resistance of the coil and the casing to see if it has been broken down. Of course, the larger the resistance, the better, and the minimum is the same, not less than 0.5 megohms.
% 0A6 ลวด เดี่ยว เฟส มอเตอร์
% 0aThe reason why there are 6 wires is actually two wires (Z1, Z2) are the wires of the centrifugal switch. This kind of motor also has 6 terminals, so its connecting piece should also be removed. The capacitor is also removed, and then measure the resistance at the beginning and end of the two-phase windings and between the two-phase windings. The method is the same as that of a three-phase motor.
% 0aEngine คุณภาพ ของ มอเตอร์ กับ a มัลติมิเตอร์ สามารถ เท่านั้น be a เบื้องต้น การตัดสิน ฉนวน ความต้านทาน ระหว่าง ขดลวด และ ฉนวน ความต้านทาน ของ แต่ละ เฟส ขดลวด ถึง พื้นดิน ควร เป็น วัด ด้วย a megohmmeter ถึง เป็น more แม่นยํา
% 0aIn addition% 2c short circuit between the turns of the winding ไม่สามารถ be measured . We can only use the method of comparison to guess wect whether there a short circuit between the turns . For example % 2c the organization of a certain phase winding is much smaller than that of the other two phases% 2c then we can suspect that there is a short circuit between turns
